Tank water heaters are a dependable way to provide a fast supply of hot water for your home. The inclusion of a storage tank ensures some hot water is always available. But over time, foreign substances can build up in the storage tank. This could be sediment or mineral buildup arriving from the main water line or a crack in the pipes. Whatever the source is, this buildup will sometimes negatively impact the efficiency of water heaters. In severe cases it can plug up drainage and may even lead to premature failure.
Fortunately, draining your water heater and removing sediment buildup is a relatively straightforward task. A certified plumber in Medina can handle the process, but you can also drain the tank yourself if you know what you’re doing. Either way, draining the tank now can help reduce the risk you’ll need premature water heater replacement.
Before You Begin…
Before you start draining the tank, you’ll want to shut off the cold water supply. The supply valve connects your water heater with the main water line. Unless you have access to a well (and you may need to drain the tank more frequently if you do), the water main provides all the potable water your home uses. Keeping the valve sealed will prevent more water from flowing into the tank, allowing you to completely empty it.
You’ll also want to get a rubber hose, like one you could use for yard work. The hose allows you to safely drain the water heater tank without spilling water all over your garage, utility closet, attic or wherever the water heater is stored. Make sure you place the other end of the hose far away from your home to stop the water from flowing back inside.
Finally, a screwdriver will help you loosen stubborn screws or valves. You shouldn’t need any more tools than this unless you stumble upon a problem with the water heater or adjacent piping. At that point, it might be best to contact a certified plumber in Medina.
Step 1: Shut Off the Water Heater
After you’ve turned off the water supply, you can shut off the water heater itself. This should be on the thermostat for natural gas water heaters or with a breaker switch for electric models. The pilot setting on gas water heaters can remain on during flushing, but electric models must be completely off. This is because of the heating elements electric water heaters use, which remain submerged. In an empty tank, they could quickly overheat. You should also review the model’s manual, as some water heaters have to be completely full before the heating elements are reactivated.
Even after you’ve shut off the water heater, you’ll have to wait for the water stored in the tank to cool down. It can be hours before the water reaches a safe temperature, so it is often best to leave the remaining steps for the following day.
Step 2: Connect the Hose to the Water Heater’s Drain Valve
Tank water heaters possess a drain valve you can use to empty the storage tank. Once you’re sure the water supply is disconnected and the water heater itself is off, go ahead and find the drain valve. Some models will have it covered up. Make sure the hose is securely fastened to prevent spilling hot water near you and the water heater.
Step 3: Open a Faucet or Other Hot Water Tap
Your home’s plumbing uses pressure inside the piping to deliver a consistent flow of water from the main water line to the rest of the house. This pressure will have to be relieved before the hot water can actually exit the tank. By heading to the closest faucet or spigot, you’ll release the pressure inside the piping. All you have to do is open the hot water tap to relieve the pressure before returning to the water heater.
Step 4: Release the Drain Valve
Keep in mind that this water may still have some residual heat. Open the drain valve and allow all the water to drain from the tank. This should pull sediment buildup out of the tank and away from your home. But some buildup might be stuck to the inside of the tank. Turning the cold water supply back on will help wash away stubborn minerals and other substances from the tank.
Repeat this step until the water appears free of sediment or minerals. If the drain isn’t working because of an obstruction, a trained plumber is likely required.
Step 5: Re-Shut the Valve Before Refilling the Water Heater
If everything proceeds like it’s supposed to, you should be able to clear out most excess sediment stuck inside your water heater. Seal up the drain valve, disconnect the hose and open the water supply to get things working again. As the water heater tank starts to fill, head back to the hot water tap you opened. Once cold water starts to flow, you know the pressure is back at appropriate levels.
At this point, you can open the gas valve or flip the breaker switch back on. Like we mentioned before, don’t forget that some models may need to be entirely full before the water can be safely heated. Make sure you check your manufacturer’s instructions before starting the process.
Keep Your Water Heater Sediment-Free for Best Results
Tank water heaters continue to be a great option for supplying your hot water needs. Draining the tank every 1-2 years will help clear out sediment buildup and keep things running at maximum efficiency. If you think your water heater is past the point of efficient heating, consider looking for water heater replacement in Medina from a technician you trust.